Besok pasti

Wednesday, January 22, 2014

Fan Motor As Wind Turbine Dynamo

I designed a Pico-class Wind Turbine With Bicycle Wheel which is using Sanden made fan motor. The resulting power of this fan motor is not as big as the power produced by permanent magnet alternator. But fan motor as dynamo is much easier to apply and affordable. Fan motor is also much cheaper and easier to buy than treadmill motor.

This fan motor is usually used to drive fan to blow ac condenser on vehicle. The photo below shows a fan motor with pulley mounted on it.

Part number: PDM-08101E (12V)

Type DC ferrite magnet

Rated voltage DC 12 (V)

Power input 76 (W)

Insulator level Class F level

Applicable voltage DC 11~15 (V)

Applicable temperatures -30~80 (°C)

Specification by Sanden Singapore

On sedan car the fan motor is mounted behind the bumper, with a fairly low height of about 50 cm from the road. It is frequently exposed to water splashes, dirt, and even flooded. Positioned only a few centimeters from a hot radiator. But it proves that the fan motor is pretty tough. Dynamo on wind turbines should be weather proof as it is always exposed to the hot sun and rain-washed.

The above drawing is dynamo pulley detail. All units are in millimeters, red fonts need to be checked on the actual dynamo shaft, as it may be different. Scale does not exactly fit the actual. Pulley is locked with a 10 mm socket wrench nut on the shaft of dynamo, as shown in the above photo. It is using mild steel round bar as material.

There are 2 set screws with allen key (hexagonal) on the side of the pulley as pegs and help to lock pulley. Allen key set screw shown in the photo below, with M6 thread diameter and length of approximately 15 to 20 mm. Set screw is fitted in a 5 mm diameter hole with M6 thread. This 5 mm diameter hole is bored through the side of pulley into the axle hole, continue to penetrate the opposite side of pulley, thus forming 2 holes for 2 set screws. When installing the pulley on dynamo shaft, position the set screw holes on pulleys so that those set screws will press flat areas on the shaft. Theore both set screws will serve also as pegs to ensure dynamo shaft turn together with pulley. It can use other type of screw, but set screw looks more tidy.

Dynamo is mounted on a fork-shaped frame of wind turbine. By using a clamp consisting of strip steel plate with 2 holes, and fastened to dynamo with 2 long 10 mm bolts (M6 thread). As shown in the photo below, Sanden dynamo has a round and flat body make it easy for installation.

To connect the large pulley on the turbine with dynamo pulley, round thermoplastic belt is used with a diameter of 5 mm Bancord brand and green color. Green Bancord has a rough surface for better traction than the orange one (smooth surface). About 1 meter long belt with open ended as off as the photo below. This belt is connected by heating with a match.

To ensure the required length of the transmission belt, position the dynamo in the middle of fork between the rim and the lower end of fork. Measure required belt length by a rope for flexible measuring tape. By positioning the dynamo in the middle between the rim and the lower end of fork, it will be a space to adjust the belt by sliding dynamo up and down.

Too high belt tension will add more load to turbine, too loose belt will make dynamo pulley slip. Both condition will reduce dynamo power. Belt tension setting is done by shifting dynamo position at fork of turbine frame. Higher dynamo position will reduce tension, while lower dynamo position will increase belt tension. I usually use a rope to tie the turbine to stop it when adjusting belt tension. Before adjustment, put dynamo at slack belt position. Connect a 12 volts battery with abaout 5AH capacity to dynamo to make dynamo pulley rotated by that battery. Lower the dynamo slowly to brake pulley rotation by belt which is also can not rotate because the turbine is tied by a rope. Continue lower the dynamo until at a point where dynamo pulley rotation almost stopped as it braked by belt. Tighten two 10 mm bolts on the fork to hold dynamo at that position. Disconnect the battery cable to the dynamo. Be sure that two 10 mm bolts are already tightened. Remove the rope that binds the turbine so that the turbine can spin when the wind blows.

ReadFull Article ..

Sunday, November 24, 2013

Memperbanyak Like pada Fan Page Facebook

Cara memperbanyak like pada fan page facebook - Bagaimana memperbanyak like pada fanpage facebook?? Pertanyaan ini yang mungkin sering muncul ketika kita membuat fan page di facebook. Apa enaknya ngeliat fanpage yang para likersnya adalah kita sendiri?? bagaikan rumah tanpa penghuni.. apalagi di pasang di blog?? waduh.. malu - maluin...

Oleh karena itu, kali ini idebagus akan kasih tahu cara untuk memperbanyak like fanpage sobat. Setahu saya ada 2 cara yang menurut saya ampuh untuk menambah like fan page facebook. Yang pertama yang menurut saya paling ampuh dan paling mujarab yaitu melalui jalur promosi. Seperti halnya sebuah produk, halaman facebook kita seharusnya di promosikan, baik pada para pengguna facebook maupun melalui blog kita.

Untuk cara yang ke 2 nya yaitu melalui Youlikehits..
Apa itu youlikehits??
Adalah website yang menawarkan membernya untuk memperoleh like secara gratis ataupun berbayar.

Nggak cuma itu sob! untuk follower di twitter juga bisa... untuk lebih jauhnya, mendingan sobat cepat daftar de.. mumpung gratis.. hehehe

Berikut cara mendaftar di Youlikehits

1. Masuk ke situs Youlikehits

2. Masukkan data yang di minta pada SignUp kemudian Klik sign Up seperti gambar berikut.

3. Seperti gambar di atas, sobat yang berhasil mendaftar bisa langsung log in ke akun youlikehits sobat. Setelah login, sobat akan di minta untuk mengisih kode verifikasi seperti gambar berikut.

4. Buka email masuk pada alamat email yang sobat daftarkan tadi. ( buka pada tab baru )
5. Ambil kode verfikasi pada email yang telah di kirimkan. Lihat gambar

6. Masukkan kode verifikasi dan klik Activate.

Nah sekarang akun sobat sudah jadi, saatnya kita masuk pada intinya..

7. Setelah mengklik activate, sobat akan langsung masuk ke dashboard sobat.

8. Karna trik kali ini yaitu untuk menambah like pada fan page facebook, sobat klik facebook kemudian klik pada add an account

9. Masukan profil facebook sobat dan juga halaman fanpage sobat kemudian klik refresh seperti gambar berikut.

10. Pilih payout 9 seperti gambar berikut.

11. Kemudian klik Ok.

12. Like satu per satu fanpage seperti tampilan berikut.

13. Klik pada tulisan Ive Liked This page untuk memberitahukan bahwa sobat telah ngelike fanpage tersebut.

Tambahan:
Sobat akan mendapatkan 50 point per hari dengan mengklik tulisan Claim 50 Free Point Daily.

Sekian dan Semoga Membantu dan tolong like fan page ane ya!!! entar ane balas ngelike!!!

ReadFull Article ..